Method #1
Method #2
Bar Joist
Method #1
Method #1
Method #2
Method #2
I
-Beam
non-tapered
flanges
Method #1
Method #1
Method #2
Method #2
T
RS
F
I
-Beam
tapered
flanges
CADDY ROD LOCK beam clamp not for use with hot dip galvanized threaded rod.
*CRLB37EG and CRLBM10EG Beam Clamps are FM® Approved when installed in method #1 & #2 orientations.
*CRLB37EG and CRLBM10EG Beam Clamps are listed per UL® 2239 and UL 203 in method #1 & #2 orientations.
**CRLBM8EG is listed per UL 2239 only in method #1 & #2 orientations.
**CRLBM8EG and CRLBM10EG Beam Clamps are VdS approved when installed in method #1 and #2 orientations (VdS Approval Number G412036).
Part
Number
Article
Number
Description
RS
T
F
CRLB37EG
N/A
3/8" CADDY® ROD LOCK Beam Clamp
3/8"
1/8" - 3/16"
250 lbs
CRLB37EG
N/A
3/8" CADDY ROD LOCK Beam Clamp
3/8"
1/4" - 3/8"
500 lbs
CRLBM8EG
390001
M8 CADDY ROD LOCK Beam Clamp
M8
3mm - 5mm
1,100 N
CRLBM8EG
390001
M8 CADDY ROD LOCK Beam Clamp
M8
6mm - 10mm
1,400 N
CRLBM10EG
390002
M10 CADDY ROD LOCK Beam Clamp
M10
3mm - 5mm
1,100 N
CRLBM10EG
390002
M10 CADDY ROD LOCK Beam Clamp
M10
6mm - 10mm
2,200 N
Part
Number
Article
Number
Description
RS
Max. Pipe diameter
supported by clamp &
threaded rod
CRLB37EG*
N/A
3/8" CADDY ROD LOCK Beam Clamp
3/8"
4"/DN100
CRLBM8EG**
390001
M8 CADDY ROD LOCK Beam Clamp
M8
DN50
CRLBM10EG*
&
**
390002
M10 CADDY ROD LOCK Beam Clamp
M10
4"/DN100
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
TECHNICAL SUPPORT:
www.erico.com
CFS410_R
INSTRUCTION SHEET
NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted.
The customer is responsible for:
a. Conformance to all governing codes.
b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified engineer.
c. Using appropriate industry standard hardware as noted above.
SAFETY INSTRUCTIONS:
All governing codes and regulations and those required by the job site must be observed.
Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.
1 OF 2
© 2009, 2010, 2011, 2012 ERICO International Corporation
WARNING:
ERICO products shall be installed and used only as indicated in ERICO product instruction sheets and training materials. Instruction sheets are available at
1.
www.erico.com
and from your ERICO customer service representative.
ERICO products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
2.
All instructions must be
completely
followed to ensure proper and safe installation and performance.
3.
Improper installation, misuse, misapplication or other failure to completely follow ERICO's instructions and warnings may cause product malfunction, property
4.
damage, serious bodily injury and death.
Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment.
5.
All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any
6.
other purpose.
CADDY
®
ROD LOCK Beam Clamp
FM is a registered certification mark of FM Approvals LLC, LTD
UL is a registered trademark of UL LLC.
VdS is a registered trademark of VdS Schadenverhütung GmbH.
(2 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern